股票配资开户歡迎您的到来!

搜産品:
熱门搜索:數控股票配资开户 股票配资开户价格 液壓股票配资开户 油壓股票配资开户
在線留言 客户服務
新聞资訊
氣动股票配资开户需要定期檢查氣动系統是否存在..
一種不錯的調校數控股票配资开户旋轉工位及模具..
股票配资开户日常这樣維護 用多少年都如新
彰化某股票配资开户廠家發生火警 烈焰沖天
股票配资开户安全保護裝置的應用推廣迫在眉睫
直觀理解股票配资开户的工作原理
股票配资开户模具需要選擇合适的下模間隙
要怎樣才能延長股票配资开户模具的使用壽命
數控折彎機系統内高性能體系結構
股票配资开户模具的拆裝保養及安裝的注意事項
聯系方式
銷售熱線:13706276178
電話:0513-88321598
傳真:0513-88321596
聯系人:範曉軍
郵箱:tpy@pjjtls.com

新聞詳情

股票配资开户廠家簡介操作股票配资开户必須遵守的安全規程

發布時間: 點擊次數:862来源: 太平洋機床

  因为股票配资开户模配具有速度快、壓力大的特點,因此選用股票配资开户作沖裁、成型有必要恪守必定的安全規程。

  1.暴露于壓機之外的股票配资开户模配傳动部件,有必要設備防護罩,制止在卸下防護罩的情況下开車或試車。
2.开車前應查看主要緊固螺釘有無松动,股票配资开户模配有無裂紋,操縱機構、自动中止設備、離合器、制动器是否正常,光滑體系有無阻塞或缺油。必要時可开空車試验。
3.設備股票配资开户模配有必要将滑塊开到下死點,閉合高度有必要正确,盡量避免偏疼載荷;模具有必要緊固牢靠,并通過試壓查看。
4.工作中留意力要會集,禁止将手和東西等物件伸進危險區内。小件必定要用专门東西(鑷子或送料機構)進行操作。模具卡住坯料時,隻準用東西去擺脫。
5.發現壓床工作反常或有反常动靜,(如連擊聲、爆裂聲)應中止送料,查看原因。如系轉动部件松动、操縱設備失靈、模具松动及殘缺,應停車修補。
6.每沖完—個工件時,手或腳有必要脫離按鈕或踏闆,以避免股票配资开户模配誤操作。
7.兩人以上操作時,應定人开車,留意協調配合好。下班前應将股票配资开户模配模具落靠,斷开電源,并進行必要的打掃。 1. press gear transmission parts exposed outside the press, it is necessary to protect the equipment cover, to prevent driving or test run when the shield is removed.
2. before driving, check whether the main fastening screws are loose or not, the punch die is equipped with no cracks, the control mechanism, automatic stop equipment, clutch and brake is normal, smooth system has no obstruction or lack of oil. Open empty car test if necessary.
3. will be equipped with necessary equipment Punch Die slider to the bottom dead center, it is necessary to correct the height, to avoid the eccentric load; the mold is necessary and tighten them through the pressure test, see.
Attention to gathering the 4. work, banning things such as hands and objects into the danger zone. Small pieces must be operated with special things (tweezers or feeding mechanism). When the mold blocks the blank, just use something to get rid of it.
5. press work abnormal or anomalous movement, (such as sound, sound burst combo) should suspend feeding, check the reason. If the rotating parts are loose, the equipment is out of order, the mold is loose and incomplete, the repair should be stopped.
6. when each piece is finished, it is necessary for the hand or foot to disengage from the button or pedal so as to avoid the incorrect operation of the punch die.
7., two or more operation, should be decided to drive, pay attention to coordination and coordination. Before the work, the punch die should be matched with the die, disconnect the power supply and carry out the necessary cleaning.

推薦産品 更多
QC12Y液壓剪闆機
QC12Y液壓剪闆機
100/3200折彎機:4+1軸
100/3200折彎機:4+1軸
液壓闆料折彎機
液壓闆料折彎機
JB23系列开式可傾股票配资开户
JB23系列开式可傾股票配资开户
45T深拉股票配资开户
45T深拉股票配资开户
YTPY32-1000四柱液壓機
YTPY32-1000四柱液壓機
300/6000折彎機
300/6000折彎機
开卷校平剪切生産線
开卷校平剪切生産線

地址:江蘇省海安縣西場鎮 / 郵編:226600 / 銷售電話:0513-88321598 / 傳真:0513-88321596
CopyRight © 版權所有 2003-2019 新牛人配资 All rights reserved.
专營:股票配资开户數控股票配资开户液壓股票配资开户股票配资开户廠家
/ 蘇公網安備32062102000179号
技術支持:旗下 SiteMap